GWINSTEK - AFG-4125AE -The AGF-4125AE is a single channel 25 MHz arbitrary function generator with amplifierAFG-4000 arbitrary function generator series is GW Instek’s first arbitrary function generator series to be equipped with an 8” large touch screen. The frequency bandwidth of the single-channel models is 25MHz, and dual- channel models feature 250MHz/100MHz/80MHz/60MHz/35MHz/25MHz frequency bandwidth selections. The entire series provides high resolution of 1μHz and has built-in standard waveforms such as sine wave, square wave, triangle wave, pulse wave, noise wave, harmonic wave, etc. The highest bandwidth 250MHz model provides 1.25GSa/s sample rate; the mid-range models ranging from 35MHz to 100MHz provide 500MSa/s sample rate; and the 25MHz entry-level models have a sampling rate of 125MSa/s. For vertical resolution, the 35MHz~250MHz models feature 16-bit resolution, and 25MHz entry-level models provide 14-bit resolution. In addition, in terms of memory depth, dual channel 25MHz ~250MHz models provide 10M memory depth, and entry-level single channel 25MHz models provide arbitrary waveform editing function with 16k memory depth. The entire series has built-in 146 arbitrary waveforms for editing and output.The dual-channel models provide dual-channel related settings such as frequency coupling, amplitude coupling and tracking, allowing users to quickly set the output related to the two channels. In terms of modulation function, the AFG-4000 series provides AM, DSB-AM, FM, PM, PWM, ASK, PSK, BPSK, QPSK, FSK, 3FSK, 4FSK, OSK, SUM and other modulation signal outputs. Standard functions include Sweep and Burst outputs and the Counter function. AFG-4125AE has a built-in power amplifier. The power output of the amplifier reaches 10W, and the amplification factor reaches 10 times to produce a maximum output of 22V. The independent input/output power amplifier provides a bandwidth range from 5Hz to 100 kHz, which can be used for audio signal and other application requirements.The AFG-4000 series is equipped with an 8-inch high-resolution TFT LCD, and models above 35MHz are equipped with the touch screen function. The configuration of touch screen makes inputting parameters more convenient. Users only need to touch parameters such as Frequency, Amplitude or DC offset, and a numeric input window will appear on the screen. Users can intuitively input parameters through this window or the numeric keys on the AFG-4000 panel. Through the 8" large screen, touch screen and diverse built-in waveforms, users can control it at will to meet their signal generation needs.As for the interfaces, the 25MHz models: AFG-4125E/ 4125AE/ 4225E have built-in USB Host/Device interfaces, and the models with higher bandwidths ranging from 35MHz to 250MHz come standard with USB Host/Device and LAN interfaces.Features- Provide single-channel or dual-channel output- Single channel:AFG-4125E/4125AE(25MHz)- Dual Channel:AFG-4225E/4235/4260/4280/4210H/4225H (25/35/60/80/100/250MHz)- Built-in Sine, Square, Triangle, Ramp, Pulse, Noise, Harmonic wave, Arbitrary wave- Min. resolution is 1μHz- Arbitrary function: Sampling rate- AFG-4225H: 1.25GSa/s- AFG-4235/ 4260/ 4280/ 4210H: 500MSa/s- AFG-4125E/ 4125AE/ 4225E: 125MSa/s- Amplitude Resolution: AFG-4125E/ 4125AE/ 4225E: 14bits- AFG-4235/ 4260/ 4280/ 4210H/ 4225H:16bits- Memory Length: AFG-4225E/AFG-4235/ 4260/ 4280/ 4210H/ 4225H: 10M/per channel- AFG-4125E/ 4125AE: 16k/per channel- Modulation: AM, DSB-AM, FM, PM, PWM, ASK, PSK, BPSK, QPSK, FSK, 3FSK, 4FSK, OSK, SUM- Built-in sweep, burst, counter function- AFG-4125AE Built-in Power Amplifier function- Communication interface: AFG-4235/ 4260/ 4280/ 4210H/ 4225H provide USB, LAN interface- AFG-4125E/ 4125AE/ 4225E provide USB interface- 8” TFT LCD Display, 800*480 resolution; Multi-Touch Display: AFG-4235/ 4260/ 4280/ 4210H/ 4225H

GWINSTEK - AFG-4125E -The AGF-4125E is a single channel 25 MHz arbitrary function generatorAFG-4000 arbitrary function generator series is GW Instek’s first arbitrary function generator series to be equipped with an 8” large touch screen. The frequency bandwidth of the single-channel models is 25MHz, and dual- channel models feature 250MHz/100MHz/80MHz/60MHz/35MHz/25MHz frequency bandwidth selections. The entire series provides high resolution of 1μHz and has built-in standard waveforms such as sine wave, square wave, triangle wave, pulse wave, noise wave, harmonic wave, etc. The highest bandwidth 250MHz model provides 1.25GSa/s sample rate; the mid-range models ranging from 35MHz to 100MHz provide 500MSa/s sample rate; and the 25MHz entry-level models have a sampling rate of 125MSa/s. For vertical resolution, the 35MHz~250MHz models feature 16-bit resolution, and 25MHz entry-level models provide 14-bit resolution. In addition, in terms of memory depth, dual channel 25MHz ~250MHz models provide 10M memory depth, and entry-level single channel 25MHz models provide arbitrary waveform editing function with 16k memory depth. The entire series has built-in 146 arbitrary waveforms for editing and output.The dual-channel models provide dual-channel related settings such as frequency coupling, amplitude coupling and tracking, allowing users to quickly set the output related to the two channels. In terms of modulation function, the AFG-4000 series provides AM, DSB-AM, FM, PM, PWM, ASK, PSK, BPSK, QPSK, FSK, 3FSK, 4FSK, OSK, SUM and other modulation signal outputs. Standard functions include Sweep and Burst outputs and the Counter function. AFG-4125AE has a built-in power amplifier. The power output of the amplifier reaches 10W, and the amplification factor reaches 10 times to produce a maximum output of 22V. The independent input/output power amplifier provides a bandwidth range from 5Hz to 100 kHz, which can be used for audio signal and other application requirements.The AFG-4000 series is equipped with an 8-inch high-resolution TFT LCD, and models above 35MHz are equipped with the touch screen function. The configuration of touch screen makes inputting parameters more convenient. Users only need to touch parameters such as Frequency, Amplitude or DC offset, and a numeric input window will appear on the screen. Users can intuitively input parameters through this window or the numeric keys on the AFG-4000 panel. Through the 8" large screen, touch screen and diverse built-in waveforms, users can control it at will to meet their signal generation needs.As for the interfaces, the 25MHz models: AFG-4125E/ 4125AE/ 4225E have built-in USB Host/Device interfaces, and the models with higher bandwidths ranging from 35MHz to 250MHz come standard with USB Host/Device and LAN interfaces.Features- Provide single-channel or dual-channel output- Single channel:AFG-4125E/4125AE(25MHz)- Dual Channel:AFG-4225E/4235/4260/4280/4210H/4225H (25/35/60/80/100/250MHz)- Built-in Sine, Square, Triangle, Ramp, Pulse, Noise, Harmonic wave, Arbitrary wave- Min. resolution is 1μHz- Arbitrary function: Sampling rate- AFG-4225H: 1.25GSa/s- AFG-4235/ 4260/ 4280/ 4210H: 500MSa/s- AFG-4125E/ 4125AE/ 4225E: 125MSa/s- Amplitude Resolution: AFG-4125E/ 4125AE/ 4225E: 14bits- AFG-4235/ 4260/ 4280/ 4210H/ 4225H:16bits- Memory Length: AFG-4225E/AFG-4235/ 4260/ 4280/ 4210H/ 4225H: 10M/per channel- AFG-4125E/ 4125AE: 16k/per channel- Modulation: AM, DSB-AM, FM, PM, PWM, ASK, PSK, BPSK, QPSK, FSK, 3FSK, 4FSK, OSK, SUM- Built-in sweep, burst, counter function- AFG-4125AE Built-in Power Amplifier function- Communication interface: AFG-4235/ 4260/ 4280/ 4210H/ 4225H provide USB, LAN interface- AFG-4125E/ 4125AE/ 4225E provide USB interface- 8” TFT LCD Display, 800*480 resolution; Multi-Touch Display: AFG-4235/ 4260/ 4280/ 4210H/ 4225H

GWINSTEK - AFG-4210H -The AGF-4210H is a dual channel 100 MHz arbitrary function generatorAFG-4000 arbitrary function generator series is GW Instek’s first arbitrary function generator series to be equipped with an 8” large touch screen. The frequency bandwidth of the single-channel models is 25MHz, and dual- channel models feature 250MHz/100MHz/80MHz/60MHz/35MHz/25MHz frequency bandwidth selections. The entire series provides high resolution of 1μHz and has built-in standard waveforms such as sine wave, square wave, triangle wave, pulse wave, noise wave, harmonic wave, etc. The highest bandwidth 250MHz model provides 1.25GSa/s sample rate; the mid-range models ranging from 35MHz to 100MHz provide 500MSa/s sample rate; and the 25MHz entry-level models have a sampling rate of 125MSa/s. For vertical resolution, the 35MHz~250MHz models feature 16-bit resolution, and 25MHz entry-level models provide 14-bit resolution. In addition, in terms of memory depth, dual channel 25MHz ~250MHz models provide 10M memory depth, and entry-level single channel 25MHz models provide arbitrary waveform editing function with 16k memory depth. The entire series has built-in 146 arbitrary waveforms for editing and output.The dual-channel models provide dual-channel related settings such as frequency coupling, amplitude coupling and tracking, allowing users to quickly set the output related to the two channels. In terms of modulation function, the AFG-4000 series provides AM, DSB-AM, FM, PM, PWM, ASK, PSK, BPSK, QPSK, FSK, 3FSK, 4FSK, OSK, SUM and other modulation signal outputs. Standard functions include Sweep and Burst outputs and the Counter function. AFG-4125AE has a built-in power amplifier. The power output of the amplifier reaches 10W, and the amplification factor reaches 10 times to produce a maximum output of 22V. The independent input/output power amplifier provides a bandwidth range from 5Hz to 100 kHz, which can be used for audio signal and other application requirements.The AFG-4000 series is equipped with an 8-inch high-resolution TFT LCD, and models above 35MHz are equipped with the touch screen function. The configuration of touch screen makes inputting parameters more convenient. Users only need to touch parameters such as Frequency, Amplitude or DC offset, and a numeric input window will appear on the screen. Users can intuitively input parameters through this window or the numeric keys on the AFG-4000 panel. Through the 8" large screen, touch screen and diverse built-in waveforms, users can control it at will to meet their signal generation needs.As for the interfaces, the 25MHz models: AFG-4125E/ 4125AE/ 4225E have built-in USB Host/Device interfaces, and the models with higher bandwidths ranging from 35MHz to 250MHz come standard with USB Host/Device and LAN interfaces.Features- Provide single-channel or dual-channel output- Single channel:AFG-4125E/4125AE(25MHz)- Dual Channel:AFG-4225E/4235/4260/4280/4210H/4225H (25/35/60/80/100/250MHz)- Built-in Sine, Square, Triangle, Ramp, Pulse, Noise, Harmonic wave, Arbitrary wave- Min. resolution is 1μHz- Arbitrary function: Sampling rate- AFG-4225H: 1.25GSa/s- AFG-4235/ 4260/ 4280/ 4210H: 500MSa/s- AFG-4125E/ 4125AE/ 4225E: 125MSa/s- Amplitude Resolution: AFG-4125E/ 4125AE/ 4225E: 14bits- AFG-4235/ 4260/ 4280/ 4210H/ 4225H:16bits- Memory Length: AFG-4225E/AFG-4235/ 4260/ 4280/ 4210H/ 4225H: 10M/per channel- AFG-4125E/ 4125AE: 16k/per channel- Modulation: AM, DSB-AM, FM, PM, PWM, ASK, PSK, BPSK, QPSK, FSK, 3FSK, 4FSK, OSK, SUM- Built-in sweep, burst, counter function- AFG-4125AE Built-in Power Amplifier function- Communication interface: AFG-4235/ 4260/ 4280/ 4210H/ 4225H provide USB, LAN interface- AFG-4125E/ 4125AE/ 4225E provide USB interface- 8” TFT LCD Display, 800*480 resolution; Multi-Touch Display: AFG-4235/ 4260/ 4280/ 4210H/ 4225H

GWINSTEK - AFG-4225E -The AGF-4225E is a dual channel 25 MHz arbitrary function generatorAFG-4000 arbitrary function generator series is GW Instek’s first arbitrary function generator series to be equipped with an 8” large touch screen. The frequency bandwidth of the single-channel models is 25MHz, and dual- channel models feature 250MHz/100MHz/80MHz/60MHz/35MHz/25MHz frequency bandwidth selections. The entire series provides high resolution of 1μHz and has built-in standard waveforms such as sine wave, square wave, triangle wave, pulse wave, noise wave, harmonic wave, etc. The highest bandwidth 250MHz model provides 1.25GSa/s sample rate; the mid-range models ranging from 35MHz to 100MHz provide 500MSa/s sample rate; and the 25MHz entry-level models have a sampling rate of 125MSa/s. For vertical resolution, the 35MHz~250MHz models feature 16-bit resolution, and 25MHz entry-level models provide 14-bit resolution. In addition, in terms of memory depth, dual channel 25MHz ~250MHz models provide 10M memory depth, and entry-level single channel 25MHz models provide arbitrary waveform editing function with 16k memory depth. The entire series has built-in 146 arbitrary waveforms for editing and output.The dual-channel models provide dual-channel related settings such as frequency coupling, amplitude coupling and tracking, allowing users to quickly set the output related to the two channels. In terms of modulation function, the AFG-4000 series provides AM, DSB-AM, FM, PM, PWM, ASK, PSK, BPSK, QPSK, FSK, 3FSK, 4FSK, OSK, SUM and other modulation signal outputs. Standard functions include Sweep and Burst outputs and the Counter function. AFG-4125AE has a built-in power amplifier. The power output of the amplifier reaches 10W, and the amplification factor reaches 10 times to produce a maximum output of 22V. The independent input/output power amplifier provides a bandwidth range from 5Hz to 100 kHz, which can be used for audio signal and other application requirements.The AFG-4000 series is equipped with an 8-inch high-resolution TFT LCD, and models above 35MHz are equipped with the touch screen function. The configuration of touch screen makes inputting parameters more convenient. Users only need to touch parameters such as Frequency, Amplitude or DC offset, and a numeric input window will appear on the screen. Users can intuitively input parameters through this window or the numeric keys on the AFG-4000 panel. Through the 8" large screen, touch screen and diverse built-in waveforms, users can control it at will to meet their signal generation needs.As for the interfaces, the 25MHz models: AFG-4125E/ 4125AE/ 4225E have built-in USB Host/Device interfaces, and the models with higher bandwidths ranging from 35MHz to 250MHz come standard with USB Host/Device and LAN interfaces.Features- Provide single-channel or dual-channel output- Single channel:AFG-4125E/4125AE(25MHz)- Dual Channel:AFG-4225E/4235/4260/4280/4210H/4225H (25/35/60/80/100/250MHz)- Built-in Sine, Square, Triangle, Ramp, Pulse, Noise, Harmonic wave, Arbitrary wave- Min. resolution is 1μHz- Arbitrary function: Sampling rate- AFG-4225H: 1.25GSa/s- AFG-4235/ 4260/ 4280/ 4210H: 500MSa/s- AFG-4125E/ 4125AE/ 4225E: 125MSa/s- Amplitude Resolution: AFG-4125E/ 4125AE/ 4225E: 14bits- AFG-4235/ 4260/ 4280/ 4210H/ 4225H:16bits- Memory Length: AFG-4225E/AFG-4235/ 4260/ 4280/ 4210H/ 4225H: 10M/per channel- AFG-4125E/ 4125AE: 16k/per channel- Modulation: AM, DSB-AM, FM, PM, PWM, ASK, PSK, BPSK, QPSK, FSK, 3FSK, 4FSK, OSK, SUM- Built-in sweep, burst, counter function- AFG-4125AE Built-in Power Amplifier function- Communication interface: AFG-4235/ 4260/ 4280/ 4210H/ 4225H provide USB, LAN interface- AFG-4125E/ 4125AE/ 4225E provide USB interface- 8” TFT LCD Display, 800*480 resolution; Multi-Touch Display: AFG-4235/ 4260/ 4280/ 4210H/ 4225H

GWINSTEK - AFG-4225H -The AGF-4225H is a dual channel 250 MHz arbitrary function generatorAFG-4000 arbitrary function generator series is GW Instek’s first arbitrary function generator series to be equipped with an 8” large touch screen. The frequency bandwidth of the single-channel models is 25MHz, and dual- channel models feature 250MHz/100MHz/80MHz/60MHz/35MHz/25MHz frequency bandwidth selections. The entire series provides high resolution of 1μHz and has built-in standard waveforms such as sine wave, square wave, triangle wave, pulse wave, noise wave, harmonic wave, etc. The highest bandwidth 250MHz model provides 1.25GSa/s sample rate; the mid-range models ranging from 35MHz to 100MHz provide 500MSa/s sample rate; and the 25MHz entry-level models have a sampling rate of 125MSa/s. For vertical resolution, the 35MHz~250MHz models feature 16-bit resolution, and 25MHz entry-level models provide 14-bit resolution. In addition, in terms of memory depth, dual channel 25MHz ~250MHz models provide 10M memory depth, and entry-level single channel 25MHz models provide arbitrary waveform editing function with 16k memory depth. The entire series has built-in 146 arbitrary waveforms for editing and output.The dual-channel models provide dual-channel related settings such as frequency coupling, amplitude coupling and tracking, allowing users to quickly set the output related to the two channels. In terms of modulation function, the AFG-4000 series provides AM, DSB-AM, FM, PM, PWM, ASK, PSK, BPSK, QPSK, FSK, 3FSK, 4FSK, OSK, SUM and other modulation signal outputs. Standard functions include Sweep and Burst outputs and the Counter function. AFG-4125AE has a built-in power amplifier. The power output of the amplifier reaches 10W, and the amplification factor reaches 10 times to produce a maximum output of 22V. The independent input/output power amplifier provides a bandwidth range from 5Hz to 100 kHz, which can be used for audio signal and other application requirements.The AFG-4000 series is equipped with an 8-inch high-resolution TFT LCD, and models above 35MHz are equipped with the touch screen function. The configuration of touch screen makes inputting parameters more convenient. Users only need to touch parameters such as Frequency, Amplitude or DC offset, and a numeric input window will appear on the screen. Users can intuitively input parameters through this window or the numeric keys on the AFG-4000 panel. Through the 8" large screen, touch screen and diverse built-in waveforms, users can control it at will to meet their signal generation needs.As for the interfaces, the 25MHz models: AFG-4125E/ 4125AE/ 4225E have built-in USB Host/Device interfaces, and the models with higher bandwidths ranging from 35MHz to 250MHz come standard with USB Host/Device and LAN interfaces.Features- Provide single-channel or dual-channel output- Single channel:AFG-4125E/4125AE(25MHz)- Dual Channel:AFG-4225E/4235/4260/4280/4210H/4225H (25/35/60/80/100/250MHz)- Built-in Sine, Square, Triangle, Ramp, Pulse, Noise, Harmonic wave, Arbitrary wave- Min. resolution is 1μHz- Arbitrary function: Sampling rate- AFG-4225H: 1.25GSa/s- AFG-4235/ 4260/ 4280/ 4210H: 500MSa/s- AFG-4125E/ 4125AE/ 4225E: 125MSa/s- Amplitude Resolution: AFG-4125E/ 4125AE/ 4225E: 14bits- AFG-4235/ 4260/ 4280/ 4210H/ 4225H:16bits- Memory Length: AFG-4225E/AFG-4235/ 4260/ 4280/ 4210H/ 4225H: 10M/per channel- AFG-4125E/ 4125AE: 16k/per channel- Modulation: AM, DSB-AM, FM, PM, PWM, ASK, PSK, BPSK, QPSK, FSK, 3FSK, 4FSK, OSK, SUM- Built-in sweep, burst, counter function- AFG-4125AE Built-in Power Amplifier function- Communication interface: AFG-4235/ 4260/ 4280/ 4210H/ 4225H provide USB, LAN interface- AFG-4125E/ 4125AE/ 4225E provide USB interface- 8” TFT LCD Display, 800*480 resolution; Multi-Touch Display: AFG-4235/ 4260/ 4280/ 4210H/ 4225H

GWINSTEK - AFG-4235 -The AGF-4235 is a dual channel 35 MHz arbitrary function generatorAFG-4000 arbitrary function generator series is GW Instek’s first arbitrary function generator series to be equipped with an 8” large touch screen. The frequency bandwidth of the single-channel models is 25MHz, and dual- channel models feature 250MHz/100MHz/80MHz/60MHz/35MHz/25MHz frequency bandwidth selections. The entire series provides high resolution of 1μHz and has built-in standard waveforms such as sine wave, square wave, triangle wave, pulse wave, noise wave, harmonic wave, etc. The highest bandwidth 250MHz model provides 1.25GSa/s sample rate; the mid-range models ranging from 35MHz to 100MHz provide 500MSa/s sample rate; and the 25MHz entry-level models have a sampling rate of 125MSa/s. For vertical resolution, the 35MHz~250MHz models feature 16-bit resolution, and 25MHz entry-level models provide 14-bit resolution. In addition, in terms of memory depth, dual channel 25MHz ~250MHz models provide 10M memory depth, and entry-level single channel 25MHz models provide arbitrary waveform editing function with 16k memory depth. The entire series has built-in 146 arbitrary waveforms for editing and output.The dual-channel models provide dual-channel related settings such as frequency coupling, amplitude coupling and tracking, allowing users to quickly set the output related to the two channels. In terms of modulation function, the AFG-4000 series provides AM, DSB-AM, FM, PM, PWM, ASK, PSK, BPSK, QPSK, FSK, 3FSK, 4FSK, OSK, SUM and other modulation signal outputs. Standard functions include Sweep and Burst outputs and the Counter function. AFG-4125AE has a built-in power amplifier. The power output of the amplifier reaches 10W, and the amplification factor reaches 10 times to produce a maximum output of 22V. The independent input/output power amplifier provides a bandwidth range from 5Hz to 100 kHz, which can be used for audio signal and other application requirements.The AFG-4000 series is equipped with an 8-inch high-resolution TFT LCD, and models above 35MHz are equipped with the touch screen function. The configuration of touch screen makes inputting parameters more convenient. Users only need to touch parameters such as Frequency, Amplitude or DC offset, and a numeric input window will appear on the screen. Users can intuitively input parameters through this window or the numeric keys on the AFG-4000 panel. Through the 8" large screen, touch screen and diverse built-in waveforms, users can control it at will to meet their signal generation needs.As for the interfaces, the 25MHz models: AFG-4125E/ 4125AE/ 4225E have built-in USB Host/Device interfaces, and the models with higher bandwidths ranging from 35MHz to 250MHz come standard with USB Host/Device and LAN interfaces.Features- Provide single-channel or dual-channel output- Single channel:AFG-4125E/4125AE(25MHz)- Dual Channel:AFG-4225E/4235/4260/4280/4210H/4225H (25/35/60/80/100/250MHz)- Built-in Sine, Square, Triangle, Ramp, Pulse, Noise, Harmonic wave, Arbitrary wave- Min. resolution is 1μHz- Arbitrary function: Sampling rate- AFG-4225H: 1.25GSa/s- AFG-4235/ 4260/ 4280/ 4210H: 500MSa/s- AFG-4125E/ 4125AE/ 4225E: 125MSa/s- Amplitude Resolution: AFG-4125E/ 4125AE/ 4225E: 14bits- AFG-4235/ 4260/ 4280/ 4210H/ 4225H:16bits- Memory Length: AFG-4225E/AFG-4235/ 4260/ 4280/ 4210H/ 4225H: 10M/per channel- AFG-4125E/ 4125AE: 16k/per channel- Modulation: AM, DSB-AM, FM, PM, PWM, ASK, PSK, BPSK, QPSK, FSK, 3FSK, 4FSK, OSK, SUM- Built-in sweep, burst, counter function- AFG-4125AE Built-in Power Amplifier function- Communication interface: AFG-4235/ 4260/ 4280/ 4210H/ 4225H provide USB, LAN interface- AFG-4125E/ 4125AE/ 4225E provide USB interface- 8” TFT LCD Display, 800*480 resolution; Multi-Touch Display: AFG-4235/ 4260/ 4280/ 4210H/ 4225H

GWINSTEK - AFG-4260 -The AGF-4260 is a dual channel 60 MHz arbitrary function generatorAFG-4000 arbitrary function generator series is GW Instek’s first arbitrary function generator series to be equipped with an 8” large touch screen. The frequency bandwidth of the single-channel models is 25MHz, and dual- channel models feature 250MHz/100MHz/80MHz/60MHz/35MHz/25MHz frequency bandwidth selections. The entire series provides high resolution of 1μHz and has built-in standard waveforms such as sine wave, square wave, triangle wave, pulse wave, noise wave, harmonic wave, etc. The highest bandwidth 250MHz model provides 1.25GSa/s sample rate; the mid-range models ranging from 35MHz to 100MHz provide 500MSa/s sample rate; and the 25MHz entry-level models have a sampling rate of 125MSa/s. For vertical resolution, the 35MHz~250MHz models feature 16-bit resolution, and 25MHz entry-level models provide 14-bit resolution. In addition, in terms of memory depth, dual channel 25MHz ~250MHz models provide 10M memory depth, and entry-level single channel 25MHz models provide arbitrary waveform editing function with 16k memory depth. The entire series has built-in 146 arbitrary waveforms for editing and output.The dual-channel models provide dual-channel related settings such as frequency coupling, amplitude coupling and tracking, allowing users to quickly set the output related to the two channels. In terms of modulation function, the AFG-4000 series provides AM, DSB-AM, FM, PM, PWM, ASK, PSK, BPSK, QPSK, FSK, 3FSK, 4FSK, OSK, SUM and other modulation signal outputs. Standard functions include Sweep and Burst outputs and the Counter function. AFG-4125AE has a built-in power amplifier. The power output of the amplifier reaches 10W, and the amplification factor reaches 10 times to produce a maximum output of 22V. The independent input/output power amplifier provides a bandwidth range from 5Hz to 100 kHz, which can be used for audio signal and other application requirements.The AFG-4000 series is equipped with an 8-inch high-resolution TFT LCD, and models above 35MHz are equipped with the touch screen function. The configuration of touch screen makes inputting parameters more convenient. Users only need to touch parameters such as Frequency, Amplitude or DC offset, and a numeric input window will appear on the screen. Users can intuitively input parameters through this window or the numeric keys on the AFG-4000 panel. Through the 8" large screen, touch screen and diverse built-in waveforms, users can control it at will to meet their signal generation needs.As for the interfaces, the 25MHz models: AFG-4125E/ 4125AE/ 4225E have built-in USB Host/Device interfaces, and the models with higher bandwidths ranging from 35MHz to 250MHz come standard with USB Host/Device and LAN interfaces.Features- Provide single-channel or dual-channel output- Single channel:AFG-4125E/4125AE(25MHz)- Dual Channel:AFG-4225E/4235/4260/4280/4210H/4225H (25/35/60/80/100/250MHz)- Built-in Sine, Square, Triangle, Ramp, Pulse, Noise, Harmonic wave, Arbitrary wave- Min. resolution is 1μHz- Arbitrary function: Sampling rate- AFG-4225H: 1.25GSa/s- AFG-4235/ 4260/ 4280/ 4210H: 500MSa/s- AFG-4125E/ 4125AE/ 4225E: 125MSa/s- Amplitude Resolution: AFG-4125E/ 4125AE/ 4225E: 14bits- AFG-4235/ 4260/ 4280/ 4210H/ 4225H:16bits- Memory Length: AFG-4225E/AFG-4235/ 4260/ 4280/ 4210H/ 4225H: 10M/per channel- AFG-4125E/ 4125AE: 16k/per channel- Modulation: AM, DSB-AM, FM, PM, PWM, ASK, PSK, BPSK, QPSK, FSK, 3FSK, 4FSK, OSK, SUM- Built-in sweep, burst, counter function- AFG-4125AE Built-in Power Amplifier function- Communication interface: AFG-4235/ 4260/ 4280/ 4210H/ 4225H provide USB, LAN interface- AFG-4125E/ 4125AE/ 4225E provide USB interface- 8” TFT LCD Display, 800*480 resolution; Multi-Touch Display: AFG-4235/ 4260/ 4280/ 4210H/ 4225H

GWINSTEK - AFG-4280 -The AGF-4280 is a dual channel 80 MHz arbitrary function generatorAFG-4000 arbitrary function generator series is GW Instek’s first arbitrary function generator series to be equipped with an 8” large touch screen. The frequency bandwidth of the single-channel models is 25MHz, and dual- channel models feature 250MHz/100MHz/80MHz/60MHz/35MHz/25MHz frequency bandwidth selections. The entire series provides high resolution of 1μHz and has built-in standard waveforms such as sine wave, square wave, triangle wave, pulse wave, noise wave, harmonic wave, etc. The highest bandwidth 250MHz model provides 1.25GSa/s sample rate; the mid-range models ranging from 35MHz to 100MHz provide 500MSa/s sample rate; and the 25MHz entry-level models have a sampling rate of 125MSa/s. For vertical resolution, the 35MHz~250MHz models feature 16-bit resolution, and 25MHz entry-level models provide 14-bit resolution. In addition, in terms of memory depth, dual channel 25MHz ~250MHz models provide 10M memory depth, and entry-level single channel 25MHz models provide arbitrary waveform editing function with 16k memory depth. The entire series has built-in 146 arbitrary waveforms for editing and output.The dual-channel models provide dual-channel related settings such as frequency coupling, amplitude coupling and tracking, allowing users to quickly set the output related to the two channels. In terms of modulation function, the AFG-4000 series provides AM, DSB-AM, FM, PM, PWM, ASK, PSK, BPSK, QPSK, FSK, 3FSK, 4FSK, OSK, SUM and other modulation signal outputs. Standard functions include Sweep and Burst outputs and the Counter function. AFG-4125AE has a built-in power amplifier. The power output of the amplifier reaches 10W, and the amplification factor reaches 10 times to produce a maximum output of 22V. The independent input/output power amplifier provides a bandwidth range from 5Hz to 100 kHz, which can be used for audio signal and other application requirements.The AFG-4000 series is equipped with an 8-inch high-resolution TFT LCD, and models above 35MHz are equipped with the touch screen function. The configuration of touch screen makes inputting parameters more convenient. Users only need to touch parameters such as Frequency, Amplitude or DC offset, and a numeric input window will appear on the screen. Users can intuitively input parameters through this window or the numeric keys on the AFG-4000 panel. Through the 8" large screen, touch screen and diverse built-in waveforms, users can control it at will to meet their signal generation needs.As for the interfaces, the 25MHz models: AFG-4125E/ 4125AE/ 4225E have built-in USB Host/Device interfaces, and the models with higher bandwidths ranging from 35MHz to 250MHz come standard with USB Host/Device and LAN interfaces.Features- Provide single-channel or dual-channel output- Single channel:AFG-4125E/4125AE(25MHz)- Dual Channel:AFG-4225E/4235/4260/4280/4210H/4225H (25/35/60/80/100/250MHz)- Built-in Sine, Square, Triangle, Ramp, Pulse, Noise, Harmonic wave, Arbitrary wave- Min. resolution is 1μHz- Arbitrary function: Sampling rate- AFG-4225H: 1.25GSa/s- AFG-4235/ 4260/ 4280/ 4210H: 500MSa/s- AFG-4125E/ 4125AE/ 4225E: 125MSa/s- Amplitude Resolution: AFG-4125E/ 4125AE/ 4225E: 14bits- AFG-4235/ 4260/ 4280/ 4210H/ 4225H:16bits- Memory Length: AFG-4225E/AFG-4235/ 4260/ 4280/ 4210H/ 4225H: 10M/per channel- AFG-4125E/ 4125AE: 16k/per channel- Modulation: AM, DSB-AM, FM, PM, PWM, ASK, PSK, BPSK, QPSK, FSK, 3FSK, 4FSK, OSK, SUM- Built-in sweep, burst, counter function- AFG-4125AE Built-in Power Amplifier function- Communication interface: AFG-4235/ 4260/ 4280/ 4210H/ 4225H provide USB, LAN interface- AFG-4125E/ 4125AE/ 4225E provide USB interface- 8” TFT LCD Display, 800*480 resolution; Multi-Touch Display: AFG-4235/ 4260/ 4280/ 4210H/ 4225H

GWINSTEK - APS-7050 -APS-7050 AC Power Source 310Vrms / 4.2Arms / 500VA / 45~999.9Hz, with universal socketGWInstek introduces APS-7000 series programmable AC power sources, which consists of 500VA of APS-7050, 1000VA of APS-7100, 2000VA of APS-7200 and 3000VA of APS-7300. APS-7000 series features power characteristics from its linear structure design including low noise, low THD, and highly stabilized power output that are ideal for the product development and verification of input power with low noise requirement or stereo, video and audio device applications, etc. The maximum rated voltage is 0~ 310Vrms, 25.2Arms, 100.8A peak current and the output frequency range is 45~500.0Hz. Users can conveniently augment the output voltage from 0Vrms to 600Vrms and output frequency from 45Hz to 999.9Hz by purchasing options without sending equipment back to GW Instek.One of the popular alternative energy solutions in the market is to utilize inverter to convert DC to AC and the converted AC is then sent to power grid or products require electricity. For instance, AC produced by PV inverter is sent to power grid or equipment requires electricity. While simulating power grid to verify inverter connecting with power grid, general AC power sources cannot withstand DUT's feedback energy, hence, additional power consumption resistors are needed to prevent AC power source from being damaged. On the contrary, APS-7000 series has the characteristic of absorbing reverse current so that additional power consumption resistors are not required. The input terminal of APS-7000 series is designed to isolate from the simulated AC power grid output terminal, therefore, users do not need an additional isolation device to protect DUT.APS-7000 series is suitable for simulating power grid and conducting inverter output characteristic tests, including synchronized phase and frequency. Reverse current and power detected by APS-7000 series will be displayed in red readings to facilitate user's test observation. APS-7000 series utilizes Simulate mode and Sequence mode to provide a single step or consecutive power changes; and to simulate power grid's Voltage Abnormality Test and Frequency Abnormality Test.Features- 4.3-inch TFT-LCD- Output capacity : APS-7050(500VA、310Vrms、4.2Arms)；APS-7100 (1000VA、310Vrms、8.4Arms)；APS-7200(2000VA、310Vrms、16.8Arms)；APS-7300 (3000VA、310Vrms、25.2Arms)；Output augmentation by options (0~600Vrms/45~999.9Hz)- Low Ripple & Noise- Measurement and test functions include VOLT、CURR、PWR、SVA、IPK、IPKH、FREQ、PF、CF- Support a small AC current measurement 2mA ~ 35A, Min. resolution 0.01mA(APS- 7050& APS-7100)- Reverse Current Alarm Function- 10 sets of Sequence function to Edit Output Waveforms/- 10 sets of simulate mode to Rapidly Simulate Transient Power Supply/- 10 sets of Program mode to Define Measurement Sequence/- 10 sets of Panel Memory Function- Automatic Execution of Sequence、Simulate、Program mode and Output Function when the Power is on- Standard Interfaces: LAN, USB Host, USB Device (APS-7200 and APS-7300 models only)- Optional Interfaces: GPIB (APS-001)；RS-232 / USB CDC(APS-002 for APS-7050& APS-7100 only)；RS-232(APS-007 for APS-7200& APS-7300 only)

GW INSTEK - APS-7050E - 500VA Linear AC Power Source 500VA, 310Vrms, 4.2/2.1Arms GW Instek launches the APS-7000E Series the economy version of the APS-7000 Series programmable AC power source. With the height of 2U, the maximum rated output for APS-7050E is 500VA, 310Vrms, 4.2Arms and APS-7100E is 1000VA, 310Vrms, 8.4Arms. The output frequency range of the series is 45~500Hz. The series is ideal for the test and development of DC power supply devices, consumer electronics, automotive electronics and electronic components.The APS-7000E Series comprises six measurement and test functions (Vrms, Irms, F, Ipk, W, PF), and provides user interface similar to that of AC Power Meter. The APS7000E Series, via switching many sets of current levels to increase small current measurement resolution, is ideal for the LED industry and standby mode power consumption test. Ten sets of Preset allow users to store ten settings. To meet the test criteria of line voltage fluctuation often seen in consumer electronics, the APS-7000E Series not only provides a stable AC power source but also features the Test mode to satisfy special or abnormal voltage and frequency variation demands.Ten sets of the Test mode simulate power outage, voltage rise, and voltage fall. The APS7000E Series that simulates waveforms of city power grid s transient changes is suitable for verifying electronics products operated under abnormal power source.The APS-7000E Series is the economy version of the APS-7000 Series. If communications interface and larger voltage/frequency are required, please refer to the APS-7000 Series.Key features:- 4.3” large LCD Display- Output Capacity: - APS-7050E(500VA, 310Vrms, 4.2/2.1Arms) - APS-7100E(1000VA, 310Vrms, 8.4/4.2Arms)- Measurement Function: Voltage, Current, Power, Frequency, Power Factor, Ipeak - Reverse Current Alarm Function- 10 Sets of The Test Mode Simulate Power Transient Output- 10 Sets of Preset Allow Users to Store Ten Settings- OCP/OPP/OTP Protection- Variable Voltage, Frequency and Current Limiter- Universal Power Inlet

GWInstek - APS-7100 -APS-7100 AC Power Source 310Vrms / 8.4Arms / 1000VA / 45~999.9Hz, with universal socket GWInstek introduces APS-7000 series programmable AC power sources, which consists of 500VA of APS-7050, 1000VA of APS-7100, 2000VA of APS-7200 and 3000VA of APS-7300. APS-7000 series features power characteristics from its linear structure design including low noise, low THD, and highly stabilized power output that are ideal for the product development and verification of input power with low noise requirement or stereo, video and audio device applications, etc. The maximum rated voltage is 0~ 310Vrms, 25.2Arms, 100.8A peak current and the output frequency range is 45~500.0Hz. Users can conveniently augment the output voltage from 0Vrms to 600Vrms and output frequency from 45Hz to 999.9Hz by purchasing options without sending equipment back to GW Instek. One of the popular alternative energy solutions in the market is to utilize inverter to convert DC to AC and the converted AC is then sent to power grid or products require electricity. For instance, AC produced by PV inverter is sent to power grid or equipment requires electricity. While simulating power grid to verify inverter connecting with power grid, general AC power sources cannot withstand DUT's feedback energy, hence, additional power consumption resistors are needed to prevent AC power source from being damaged. On the contrary, APS-7000 series has the characteristic of absorbing reverse current so that additional power consumption resistors are not required. The input terminal of APS-7000 series is designed to isolate from the simulated AC power grid output terminal, therefore, users do not need an additional isolation device to protect DUT. APS-7000 series is suitable for simulating power grid and conducting inverter output characteristic tests, including synchronized phase and frequency. Reverse current and power detected by APS-7000 series will be displayed in red readings to facilitate user's test observation. APS-7000 series utilizes Simulate mode and Sequence mode to provide a single step or consecutive power changes; and to simulate power grid's Voltage Abnormality Test and Frequency Abnormality Test. Features - 4.3-inch TFT-LCD - Output capacity : APS-7050(500VA、310Vrms、4.2Arms)；APS-7100 (1000VA、310Vrms、8.4Arms)；APS-7200(2000VA、310Vrms、16.8Arms)；APS-7300 (3000VA、310Vrms、25.2Arms)；-Output augmentation by options (0~600Vrms/45~999.9Hz) - Low Ripple & Noise - Measurement and test functions include VOLT、CURR、PWR、SVA、IPK、IPKH、FREQ、PF、CF- Support a small AC current measurement 2mA ~ 35A, Min. resolution 0.01mA(APS- 7050& APS-7100) - Reverse Current Alarm Function - 10 sets of Sequence function to Edit Output Waveforms/ - 10 sets of simulate mode to Rapidly Simulate Transient Power Supply/ - 10 sets of Program mode to Define Measurement Sequence/ - 10 sets of Panel Memory Function - Automatic Execution of Sequence、Simulate、Program mode and Output Function when the Power is on - Standard Interfaces: LAN, USB Host, USB Device (APS-7200 and APS-7300 models only) - Optional Interfaces: GPIB (APS-001)；RS-232 / USB CDC(APS-002 for APS-7050& APS-7100 only)；RS-232(APS-007 for APS-7200& APS-7300 only)

GW INSTEK - APS-7100E - 1000VA Linear AC Power Source 1000VA, 310Vrms, 8.4ArmsGW Instek launches the APS-7000E Series the economy version of the APS-7000 Series programmable AC power source. With the height of 2U, the maximum rated output for APS-7050E is 500VA, 310Vrms, 4.2Arms and APS-7100E is 1000VA, 310Vrms, 8.4Arms. The output frequency range of the series is 45~500Hz. The series is ideal for the test and development of DC power supply devices, consumer electronics, automotive electronics and electronic components.The APS-7000E Series comprises six measurement and test functions (Vrms, Irms, F, Ipk, W, PF), and provides user interface similar to that of AC Power Meter. The APS7000E Series, via switching many sets of current levels to increase small current measurement resolution, is ideal for the LED industry and standby mode power consumption test. Ten sets of Preset allow users to store ten settings.To meet the test criteria of line voltage fluctuation often seen in consumer electronics, the APS-7000E Series not only provides a stable AC power source but also features the Test mode to satisfy special or abnormal voltage and frequency variation demands. Ten sets of the Test mode simulate power outage, voltage rise, and voltage fall. The APS7000E Series that simulates waveforms of city power grid s transient changes is suitable for verifying electronics products operated under abnormal power source.The APS-7000E Series is the economy version of the APS-7000 Series. If communications interface and larger voltage/frequency are required, please refer to the APS-7000 Series. Key features:- 4.3” large LCD Display- Output Capacity:   - APS-7050E(500VA, 310Vrms, 4.2/2.1Arms)  - APS-7100E(1000VA, 310Vrms, 8.4/4.2Arms)- Measurement Function: Voltage, Current, Power, Frequency, Power Factor, Ipeak - Reverse Current Alarm Function- 10 Sets of The Test Mode Simulate Power Transient Output- 10 Sets of Preset Allow Users to Store Ten Settings- OCP/OPP/OTP Protection- Variable Voltage, Frequency and Current Limiter- Universal Power Inlet

GWInstek - ASR-2050R - ASR-2050 (Universal), Programmable AC/DC Power Source, 500VA(RS232,USB+LAN)  (CE), 350V / 10A / 500VA / 999.9HzThe ASR-2000 series, an AC+DC power source designed for system integration or desktop applications, offers both a rated output power for the AC output and a rated output power for the DC output. Nine ASR-2000 output modes are available, including 1) AC power output mode (AC-INT mode), 2) DC power output mode (DC-INT mode), 3) AC/DC power output mode (AC+DC-INT mode), 4) External AC signal source mode (AC-EXT mode), 5) External AC/DC signal source mode (AC+DC-EXT mode), 6) External AC signal superimposition mode (AC-ADD mode), 7) External AC/DC signal superimposition mode (AC+DC-ADD mode), 8) External AC signal synchronization mode (AC-SYNC mode), 9) External AC/DC signal synchronization mode (AC+DC-SYNC mode).The ASR-2000 series provides users with the ability to output waveforms to meet the testing requirements of various electronic components, automotive electrical equipment, and household appliances, including 1) Sequence mode for generating waveform drops, surges, sags, changes, and other abnormal power conditions; 2) Arbitrary waveform function, which allows users to save and upload custom waveforms; and The ASR-2000 series, an AC+DC power source designed for system integration or desktop applications, offers both a rated output power for the AC output and a rated output power for the DC output. 3) Simulation mode for simulating power failure, voltage surge, voltage dip, and frequency fluctuations. When the ASR-2000 series power supply outputs, it can also output Vrms, Vavg, Vpeak, Irms, Iavg, Ipeak, IpkH, P, S, Q, PF, CF, voltage harmonics, and current harmonics 40. In addition, the remote sense function ensures accurate voltage output. With the Customized Phase Angle for Output On/Off function, the start and end angles of the voltage output can be set according to the test requirements. The settings of the V-Limit, Ipeak-Limit, F-Limit, OVP, OCP, OPP functions can protect the device under test during the measurement process. In addition to OTP, OCP, and OPP protection, the ASR-2000 series features a fan failure alarm function and an AC failure alarm function.  Key features - Output power: AC 0-350 Vrms, DC 0-±500 V - Output frequency up to 999.9 Hz - DC output (100% of rated power) - Measured variables: Vrms, Vavg, Vpeak, Irms, IpkH, Iavg, Ipeak, P, S, Q, PF, CF - Harmonic analysis of voltage and current (THDv, THDi) - Remote sensing function - OVP, OCP, OPP, OTP, AC failure detection, and fan failure alarm. - Support for the “Arbitrary Waveform” function - Output capacity: 500 VA / 1000 VA - User-defined phase angle for output on/off - Sequence and simulation function (up to 10 sets) - Interface: USB, LAN (std.); RS-232 + GPIB (opt.)- Built-in external control I/O and external signal input Built-in output relay control- Memory function (up to 10 devices) - Built-in web server

GWInstek - ASR-2050R - ASR-2050R is an AV+DC Power Source 350V / 10A / 500VA / 999.9Hz / without fron Power ConnectorThe ASR-2000 series, an AC+DC power source designed for system integration or desktop applications, offers both a rated output power for the AC output and a rated output power for the DC output. Nine ASR-2000 output modes are available, including 1) AC power output mode (AC-INT mode), 2) DC power output mode (DC-INT mode), 3) AC/DC power output mode (AC+DC-INT mode), 4) External AC signal source mode (AC-EXT mode), 5) External AC/DC signal source mode (AC+DC-EXT mode), 6) External AC signal superimposition mode (AC-ADD mode), 7) External AC/DC signal superimposition mode (AC+DC-ADD mode), 8) External AC signal synchronization mode (AC-SYNC mode), 9) External AC/DC signal synchronization mode (AC+DC-SYNC mode).The ASR-2000 series provides users with the ability to output waveforms to meet the testing requirements of various electronic components, automotive electrical equipment, and household appliances, including 1) Sequence mode for generating waveform drops, surges, sags, changes, and other abnormal power conditions; 2) Arbitrary waveform function, which allows users to save and upload custom waveforms; and The ASR-2000 series, an AC+DC power source designed for system integration or desktop applications, offers both a rated output power for the AC output and a rated output power for the DC output. 3) Simulation mode for simulating power failure, voltage surge, voltage dip, and frequency fluctuations. When the ASR-2000 series power supply outputs, it can also output Vrms, Vavg, Vpeak, Irms, Iavg, Ipeak, IpkH, P, S, Q, PF, CF, voltage harmonics, and current harmonics 40. In addition, the remote sense function ensures accurate voltage output. With the Customized Phase Angle for Output On/Off function, the start and end angles of the voltage output can be set according to the test requirements. The settings of the V-Limit, Ipeak-Limit, F-Limit, OVP, OCP, OPP functions can protect the device under test during the measurement process. In addition to OTP, OCP, and OPP protection, the ASR-2000 series features a fan failure alarm function and an AC failure alarm function.Key features- Output power: AC 0-350 Vrms, DC 0-±500 V- Output frequency up to 999.9 Hz- DC output (100% of rated power)- Measured variables: Vrms, Vavg, Vpeak, Irms, IpkH, Iavg, Ipeak, P, S, Q, PF, CF- Harmonic analysis of voltage and current (THDv, THDi)- Remote sensing function- OVP, OCP, OPP, OTP, AC failure detection, and fan failure alarm.- Support for the “Arbitrary Waveform” function- Output capacity: 500 VA / 1000 VA- User-defined phase angle for output on/off- Sequence and simulation function (up to 10 sets)- Interface: USB, LAN (std.); RS-232 + GPIB (opt.)- Built-in external control I/O and external signal input Built-in output relay control- Memory function (up to 10 devices)- Built-in web server

GW INSTEK - ASR-2100 - (Universal)Programmable AC/DC Power Source, 1000VA, (RS232,USB+LAN) (CE)The ASR-2000 series, an AC+DC power source aiming for system integration or desktop applications, provides both rated power output for AC output and rated power output for DC output. Nine ASR-2000 output modes are available, including 1) AC power output mode (AC-INT Mode), 2) DC power output mode (DC-INT Mode), 3) AC/DC power output mode (AC+DC-INT Mode), 4) External AC signal source mode (AC-EXT Mode), 5) External AC/DC signal source mode (AC+DC-EXT Mode), 6) External AC signal superposition mode (AC-ADD Mode), 7) External AC/DC signal superposition mode (AC+DC-ADD Mode), 8) External AC signal synchronization mode (AC-SYNC Mode), 9) External AC/DC signal synchronization mode (AC+DC-SYNC Mode).The ASR-2000 series provides users with waveform output capabilities to meet the test requirements of different electronic component development, automotive electrical devices and home appliance, including 1) Sequence mode generates waveform fallings, surges, sags, changes and other abnormal power line conditions; 2) Arbitrary waveform function allows users to store/upload user-defined waveforms; and 3) Simulate mode simulates power outage, voltage rise, voltage fall, and frequency variations. When the ASR-2000 series power source outputs, it can also measure Vrms, Vavg, Vpeak, Irms, Iavg, Ipeak, IpkH, P, S, Q, PF, CF, 40th-order Voltage Harmonic and Current Harmonic. In addition, the Remote sense function ensures accurate voltage output. The Customized Phase Angle for Output On/Off function can set the starting angle and ending angle of the voltage output according to the test requirements. V-Limit, Ipeak-Limit, F-Limit, OVP, OCP, OPP function settings can protect the DUT during the measurement process. In addition to OTP, OCP, and OPP protection, the ASR-2000 series also incorporates the Fan fail alarm function and AC fail alarm function.Key features:- Output Rating: AC 0 – 350 Vrms, DC 0 - ± 500 V- Output Frequency up to 999.9 Hz- DC Output (100% of Rated Power)- Measurement Items: Vrms, Vavg, Vpeak, Irms, IpkH, Iavg, Ipeak, P, S, Q, PF, CF- Voltage and Current Harmonic Analysis(THDv, THDi)- Remote Sensing Capability- OVP, OCP, OPP, OTP, AC Fail Detection and Fan Fail Alarm. - Support Arbitrary Waveform Function- Output Capacity: 500VA / 1000VA- Customized Phase Angle for Output On/Off- Sequence and Simulation Function(up to 10 sets)- Interface: USB, LAN(std.); RS-232+GPIB(opt.)- Built-in External Control I/O and External Signal Input- Built-in Output Relay Control- Memory Function (up to 10 sets)- Built-in Web Server

GWInstek - ASR-2100R -ASR-2100R (RACK USE), Programmable AC/DC Power Source, 1000VA, (RS232,USB+LAN) (CE)The ASR-2000 series, an AC+DC power source designed for system integration or desktop applications, offers both a rated output power for the AC output and a rated output power for the DC output. Nine ASR-2000 output modes are available, including 1) AC power output mode (AC-INT mode), 2) DC power output mode (DC-INT mode), 3) AC/DC power output mode (AC+DC-INT mode), 4) External AC signal source mode (AC-EXT mode), 5) External AC/DC signal source mode (AC+DC-EXT mode), 6) External AC signal superimposition mode (AC-ADD mode), 7) External AC/DC signal superimposition mode (AC+DC-ADD mode), 8) External AC signal synchronization mode (AC-SYNC mode), 9) External AC/DC signal synchronization mode (AC+DC-SYNC mode).The ASR-2000 series provides users with the ability to output waveforms to meet the testing requirements of various electronic components, automotive electrical equipment, and household appliances, including 1) Sequence mode for generating waveform drops, surges, sags, changes, and other abnormal power conditions; 2) Arbitrary waveform function, which allows users to save and upload custom waveforms; and The ASR-2000 series, an AC+DC power source designed for system integration or desktop applications, offers both a rated output power for the AC output and a rated output power for the DC output. 3) Simulation mode for simulating power failure, voltage surge, voltage dip, and frequency fluctuations. When the ASR-2000 series power supply outputs, it can also output Vrms, Vavg, Vpeak, Irms, Iavg, Ipeak, IpkH, P, S, Q, PF, CF, voltage harmonics, and current harmonics 40. In addition, the remote sense function ensures accurate voltage output. With the Customized Phase Angle for Output On/Off function, the start and end angles of the voltage output can be set according to the test requirements. The settings of the V-Limit, Ipeak-Limit, F-Limit, OVP, OCP, OPP functions can protect the device under test during the measurement process. In addition to OTP, OCP, and OPP protection, the ASR-2000 series features a fan failure alarm function and an AC failure alarm function.Key features- Output power: AC 0-350 Vrms, DC 0-±500 V- Output frequency up to 999.9 Hz- DC output (100% of rated power)- Measured variables: Vrms, Vavg, Vpeak, Irms, IpkH, Iavg, Ipeak, P, S, Q, PF, CF- Harmonic analysis of voltage and current (THDv, THDi)- Remote sensing function- OVP, OCP, OPP, OTP, AC failure detection, and fan failure alarm.- Support for the “Arbitrary Waveform” function- Output capacity: 500 VA / 1000 VA- User-defined phase angle for output on/off- Sequence and simulation function (up to 10 sets)- Interface: USB, LAN (std.); RS-232 + GPIB (opt.)- Built-in external control I/O and external signal input Built-in output relay control- Memory function (up to 10 devices)- Built-in web server

GW INSTEK - ASR-3200 - Programmable AC-DC Power Source, 2000VA USB+LAN+RS-232-GPIBThe ASR-3200 is an AC+DC power source, featuring high-speed DC voltage rising and falling time (100 us). Output Capacity: 2 kVAThe ASR-3200 can provide rated power output during AC output and DC output. Nine ASR-3200 output modes are available, including: 1. AC power output mode (AC-INT Mode) 2. DC power output mode (DC-INT Mode) 3. AC/DC power output mode (AC+DC-INT Mode) 4. External AC signal source mode (AC-EXT Mode) 5. External AC/DC signal source mode (AC+DC-EXT Mode) 6. External AC signal superimposition mode (AC-ADD Mode) 7. External AC/DC signal superimposition mode (AC+DC-ADD Mode) 8. External AC signal synchronization mode (AC-SYNC Mode) 9. External AC/DC signal synchronization mode (AC+DC-SYNC Mode)The ASR-3200 is ideal for the development of On-board Chargers, Server Powers, LED modules, AC Motors, AC Fans, UPS and various electronic components, as well as for testing applications of automotive electrical equipment and home appliances.Key features:- Output Rating: AC 0−400 Vrms, DC 0−570 V- Output Frequency up to 999.9 Hz- DC Output (100 % of Rated Power)- Measurement Items: Vrms, Vavg, Vpeak, Irms, IpkH, Iavg, Ipeak, P, S, Q, PF, CF- Voltage and Current Harmonic Analysis(THDv, THDi)- Remote Sensing Capability- OCP, OPP, OTP, AC Fail Detection and Fan Fail Alarm- Support Arbitrary Waveform Function- Output Capacity: 2 kVA- Customized Phase Angle for Output On/Off- Sequence and Simulation Function (up to 10 sets)- Interface: USB, LAN, RS-232, GPIB- Built-in External Control I/O and External Signal Input- Built-in Output Relay Control- Memory Function (up to 10 sets)- Built-in Web Server

GW INSTEK - ASR-3300 - Programmable AC-DC Power Source, 3000VA USB+LAN+RS-232-GPIBThe ASR-3300 is an AC+DC power source, featuring high-speed DC voltage rising and falling time (100 us). Output Capacity: 3 kVA The ASR-3300 can provide rated power output during AC output and DC output. Nine ASR-3300 output modes are available, including: 1. AC power output mode (AC-INT Mode) 2. DC power output mode (DC-INT Mode) 3. AC/DC power output mode (AC+DC-INT Mode) 4. External AC signal source mode (AC-EXT Mode) 5. External AC/DC signal source mode (AC+DC-EXT Mode) 6. External AC signal superimposition mode (AC-ADD Mode) 7. External AC/DC signal superimposition mode (AC+DC-ADD Mode) 8. External AC signal synchronization mode (AC-SYNC Mode) 9. External AC/DC signal synchronization mode (AC+DC-SYNC Mode)The ASR-3300 is ideal for the development of On-board Chargers, Server Powers, LED modules, AC Motors, AC Fans, UPS and various electronic components, as well as for testing applications of automotive electrical equipment and home appliances.Key features:- Output Rating: AC 0−400 Vrms, DC 0−570 V- Output Frequency up to 999.9 Hz- DC Output (100% of Rated Power)- Measurement Items: Vrms, Vavg, Vpeak, Irms, IpkH, Iavg, Ipeak, P, S, Q, PF, CF- Voltage and Current Harmonic Analysis(THDv, THDi)- Remote Sensing Capability- OCP, OPP, OTP, AC Fail Detection and Fan Fail Alarm- Support Arbitrary Waveform Function- Output Capacity: 3 kVA- Customized Phase Angle for Output On/Off- Sequence and Simulation Function (up to 10 sets)- Interface: USB, LAN, RS-232, GPIB- Built-in External Control I/O and External Signal Input- Built-in Output Relay Control- Memory Function (up to 10 sets)- Built-in Web Server

GW INSTEK - ASR-3400 - Programmable AC-DC Power Source, 4000VA USB+LAN+RS-232- GPIB EU socketThe ASR-3400 is an AC+DC power source, featuring high-speed DC voltage rising and falling time (100 us). Output Capacity: 4 kVA. The ASR-3400 can provide rated power output during AC output and DC output. Nine ASR-3400 output modes are available, including: 1. AC power output mode (AC-INT Mode) 2. DC power output mode (DC-INT Mode) 3. AC/DC power output mode (AC+DC-INT Mode) 4. External AC signal source mode (AC-EXT Mode) 5. External AC/DC signal source mode (AC+DC-EXT Mode) 6. External AC signal superimposition mode (AC-ADD Mode) 7. External AC/DC signal superimposition mode (AC+DC-ADD Mode) 8. External AC signal synchronization mode (AC-SYNC Mode) 9. External AC/DC signal synchronization mode (AC+DC-SYNC Mode)The ASR-3400 is ideal for the development of On-board Chargers, Server Powers, LED modules, AC Motors, AC Fans, UPS and various electronic components, as well as for testing applications of automotive electrical equipment and home appliances.Key features:- Output Rating: AC 0−400 Vrms, DC 0−570 V- Output Frequency up to 999.9 Hz > DC Output (100% of Rated Power)- Measurement Items: Vrms, Vavg, Vpeak, Irms, IpkH, Iavg, Ipeak, P, S, Q, PF, CF- Voltage and Current Harmonic Analysis(THDv, THDi)- Remote Sensing Capability- OCP, OPP, OTP, AC Fail Detection and Fan Fail Alarm- Support Arbitrary Waveform Function- Output Capacity: 4 kVA- Customized Phase Angle for Output On/Off- Sequence and Simulation Function (up to 10 sets)- Interface: USB, LAN, RS-232, GPIB- Built-in External Control I/O and External Signal Input- Built-in Output Relay Control- Memory Function (up to 10 sets)- Built-in Web Server

GW INSTEK - ASR-3400HF - Programmable AC-DC Power Source- 4000VA USB+LAN+RS-232-GPIB 5KHzThe ASR-3400HF is an AC+DC power source, featuring high-speed DC voltage rising and falling time (100 us). Output Capacity: 4 kVA. The ASR-3400 can provide rated power output during AC output and DC output. The only difference is that ASR-3400HF output frequency can reach 5 kHz (Crest factor = 4).Nine ASR-3400 output modes are available, including:1. AC power output mode (AC-INT Mode)2. DC power output mode (DC-INT Mode)3. AC/DC power output mode (AC+DC-INT Mode) 4. External AC signal source mode (AC-EXT Mode) 5. External AC/DC signal source mode (AC+DC-EXT Mode) 6. External AC signal superimposition mode (AC-ADD Mode)7. External AC/DC signal superimposition mode (AC+DC-ADD Mode)8. External AC signal synchronization mode (AC-SYNC Mode)9. External AC/DC signal synchronization mode (AC+DC-SYNC Mode)The ASR-3400 is ideal for the development of On-board Chargers, Server Powers, LED modules, AC Motors, AC Fans, UPS and various electronic components, as well as for testing applications of automotive electrical equipment and home appliances.Key features:- Output Rating: AC 0−400 Vrms, DC 0−570 V- Output Frequency up to 5kHz- DC Output (100% of Rated Power)- Measurement Items: Vrms, Vavg, Vpeak, Irms, IpkH, Iavg, Ipeak, P, S, Q, PF, CF- Voltage and Current Harmonic Analysis(THDv, THDi)- Remote Sensing Capability- OCP, OPP, OTP, AC Fail Detection and Fan Fail Alarm- Support Arbitrary Waveform Function- Output Capacity: 4 kVA- Customized Phase Angle for Output On/Off- Sequence and Simulation Function (up to 10 sets)- Interface: USB, LAN, RS-232, GPIB- Built-in External Control I/O and External Signal Input- Built-in Output Relay Control- Memory Function (up to 10 sets)- Built-in Web Server

GW INSTEK - ASR-3500 - Programmable AC-DC Power Source, 400Vrms/570Vdc / 50A/25A / 5kVA, Universal socketThe ASR-3000 series is an AC+DC power source, featuring high-speed DC voltage rising and falling time (≦100 μs). ASR-3000 is ideal for the development of On-board Chargers, Server Powers, LED modules, AC Motors, AC Fans, UPS, and various electronic components, as well as for testing applications of automotive electrical equipment and home appliances.There are five models of the series:1. ASR-3200(2 kVA)2. ASR-3300(3 kVA)3. ASR-3400(4 kVA)4. ASR-3400HF(4 kVA, Frequency upto 5 kHz)5. ASR-3500 (5 kVA)The series can provide rated power output during AC output and DC output. Ten ASR-3000 output modes are available.AC power output mode (AC-INT Mode)DC power output mode (DC-INT Mode)AC/DC power output mode (AC+DC-INT Mode) External AC signal source mode (AC-EXT Mode) External AC/DC signal source mode (AC+DC-EXT Mode) External AC signal superimposition mode (AC-ADD Mode) External AC/DC signal superimposition mode (AC+DC-ADD Mode) External AC signal synchronization mode (AC-SYNC Mode) External AC/DC signal synchronization mode (AC+DC-SYNC Mode) External DC voltage control of AC output mode (AC-VCA) Features Output Rating: AC 0 Vrms to 400 Vrms, DC 0 V to ± 570 V Output Frequency up to 999.9 Hz (ASR-3400HF up to 5000 Hz) DC Output (100 % of Rated Power) Measurement Items: Vrms, Vavg, Vpeak, Irms, IpkH, Iavg, Ipeak, P, S, Q, PF, CF Voltage and Current Harmonic Analysis(THDv, THDi) Remote Sensing Capability OCP, OPP, OTP, AC Fail Detection and Fan Fail Alarm Support Arbitrary Waveform Function Output Capacity: 2 kVA / 3 kVA /4 kVA / 5 kVA Customized Phase Angle for Output On/Off Sequence and Simulation Function(up to 10 sets) Interface(std): USB, LAN, RS-232, GPIB Built-in External Control I/O and External Signal Input Built-in Output Relay Control Memory Function (up to 10 sets) Built-in Web Server

GW INSTEK - ASR-6450 The Inception of ASR-6000 High Performance AC/DC Power Source Development, 4.5kVA Multi-outputFrom the very moment Alpha Go defeated the human chess champion with its ultra-high-speed computing capability, artificial intelligence technology (AI) has developed rapidly around the world. Today, servers with advanced AI functions process tremendous amounts of data under the high-speed computing architecture of 2 CPUs + 8 GPUs.However, AI servers require a huge amount of power to maintain high-speed computing! In order to meet this demand, the power, density and efficiency of server power supplies have been greatly improved. High-power server power modules require high-efficiency conversion and saving of power consumption.  AC single-phase input, HVDC 400V input or increased DC voltage output designs can be utilized to achieve this purpose.In order to ensure power stability when high-power servers are operating, power modules with hot-swappable redundant power supply specifications (such as CRPS) have been widely applied in server racks. Power modules with redundant functions require testing of multiple power modules at a time to ensure that all modules can maintain normal operation during high power output. Due to the rapid changes in the development of server power supplies, GW Instek developed the brand new flagship model ASR-6000 series to meet customer needs.The ASR-6000 series has two models - ASR-6450 AC / DC 4.5kVA and ASR-6600 AC / DC 6kVAASR-6000 is the first stand-alone unit from GW Instek that supports AC single/three-phase input and output, and has rated DC power output. The series employs third-generation semiconductor silicon carbide (SiC) technology to create a 4U 6kVA high power density and high-performance AC /DC power source.ASR-6000 has the ability to emulate more diverse power environment changes, such as balanced three-phase and unbalanced three-phase, phase loss, and features multi-channel output function can test up to three DUTs at the same time, programmable output impedance adjustment, and built-in over 40 types of arbitrary waveform outputs. The invincible launch of GW Instek flagship model ASR-6000 demonstrates that GW Instek can provide a complete test solution for high-power AC sources. ASR-6000 is the MVP of GW Instek power sources.ASR-6000 main applicationServer/communication power supply manufacturer6kVA On-board chargerUninterruptible power supply system (UPS)AC inverterAC three-phase motor control, and protection deviceMilitary industry, scientific research, educationFeaturesAdopts third-generation semiconductor silicon carbide (SiC) technology to create a 4U 6kVA high-performance AC/DC power source with high power densityAC input supports single-phase and three-phase, phase voltage 200V to 240V±10% (Delta or Y connection)10 output modes: including external input signal frequency and mains synchronization (SYNC), external voltage controlled internal amplifier output (VCA)Multi-channel output functionSupports 1P2W, 1P3W, 3P4W outputAC maximum output phase voltage: 350Vrms line voltage: 700VrmsAC balanced and unbalanced three-phase, phase loss output functionsProgrammable output impedance adjustmentDual-channel voltage/current output monitoring functionVoltage output rise time can be adjusted in three rangesSupports sequence editing and emulation output modePowerful arbitrary waveform editing and output function, capable of editing and outputting tens of thousands of waveformsAdvanced web server control to support data acquisition function100th order harmonic measurement functionSupports external parallel connection to increase output powerStandard interfaces: RS-232C, USB, LANOptional interfaces: CAN Bus, DeviceNet, GPIB

GWINSTEK - ASR-6450-09 GW Instek ASR-6450-09 is a 9kVA AC/DC Rack Type Power SourceThe Inception of ASR-6000 High Performance AC/DC Power Source DevelopmentFrom the very moment Alpha Go defeated the human chess champion with its ultra-high-speed computing capability, artificial intelligence technology (AI) has developed rapidly around the world. Today, servers with advanced AI functions process tremendous amounts of data under the high-speed computing architecture of 2 CPUs + 8 GPUs.However, AI servers require a huge amount of power to maintain high-speed computing! In order to meet this demand, the power, density and efficiency of server power supplies have been greatly improved. High-power server power modules require high-efficiency conversion and saving of power consumption. AC single-phase input, HVDC 400 V input or increased DC voltage output designs can be utilized to achieve this purpose.In order to ensure power stability when high-power servers are operating, power modules with hot-swappable redundant power supply specifications (such as CRPS) have been widely applied in server racks. Power modules with redundant functions require testing of multiple power modules at a time to ensure that all modules can maintain normal operation during high power output. Due to the rapid changes in the development of server power supplies, GW Instek developed the brand new flagship model ASR-6000 series to meet customer needs.ASR-6000 has the ability to emulate more diverse power environment changes, such as balanced three-phase and unbalanced three-phase, phase loss, and features multi-channel output function can test up to three DUTs at the same time, programmable output impedance adjustment, and built-in over 40 types of arbitrary waveform outputs. The invincible launch of GW Instek flagship model ASR-6000 demonstrates that GW Instek can provide a complete test solution for high-power AC sources. ASR-6000 is the MVP of GW Instek power sources.ASR-6000 main application- Server/communication power supply manufacturer- 3.6 kVA to 22 kVA On-board charger- Uninterruptible power supply system (UPS)- AC inverter- AC three-phase motor control, and protection device- Military industry, scientific research, educationTo Fulfil High Power Testing RequirementsThe ASR-6000 series offers 9 kVA, 12 kVA, 13.5 kVA, 18 kVA, 24 kVA, 30 kVA, 36 kVA rack-type models capable of outputting up to 36 kVA AC (single/three-phase) and 36 kW DC high power. The series features high-efficiency power output and stable and reliable power quality, making it suitable for high power related product testing applications.Application Fields:- CRPS Server Power Supply Testing- Three-Phase Motor Protection Device Testing- High Power UPS Testing- High Power Inverter Testing- Aerospace Equipment TestingFeatures- Adopts compound semiconductor silicon carbide (SiC) technology to create a 4U 6 kVA high-performance AC/DC power source with high power density- AC input supports single-phase and three-phase, phase voltage 200 V to 240 V±10 % (Delta or Y connection- 10 output modes: including external input signal frequency and mains synchronization (SYNC), external voltage controlled internal amplifier output (VCA)- Multi-channel output function- Supports 1P2W, 1P3W, 3P4W output- AC maximum output phase voltage: 350 Vrms line voltage: 700 Vrms- Frequency Range ：AC Mode: 15.00 Hz to 2000.0 Hz, AC+DC Mode: 1.00 Hz to 2000.0 Hz (Stand-alone unit ASR-6450/6600)；Parallel Rack Type：highest frequency de-rating to 1000.0 Hz (9 kVA to 18 kVA)；de-rating to 550.0 Hz (24 kVA to 36 kVA)- AC balanced and unbalanced three-phase, phase loss output function- Programmable output impedance adjustment- Dual-channel voltage/current output monitoring function- Voltage output rise time can be adjusted in three ranges- Supports sequence editing and emulation output mode- Powerful arbitrary waveform editing and output function, capable of editing and outputting tens of thousands of waveforms- Advanced web server control to support data acquisition function- 100th order harmonic measurement function- Support Parallel Connection Type Up to 36 kVA / 36 kW Maximum- Standard interfaces: RS-232C, USB, LAN- Optional interfaces: CAN Bus, DeviceNet, GPIB

GW INSTEK - ASR-6600 The Inception of ASR-6000 High Performance AC/DC Power Source DevelopmentFrom the very moment Alpha Go defeated the human chess champion with its ultra-high-speed computing capability, artificial intelligence technology (AI) has developed rapidly around the world. Today, servers with advanced AI functions process tremendous amounts of data under the high-speed computing architecture of 2 CPUs + 8 GPUs.However, AI servers require a huge amount of power to maintain high-speed computing! In order to meet this demand, the power, density and efficiency of server power supplies have been greatly improved. High-power server power modules require high-efficiency conversion and saving of power consumption.  AC single-phase input, HVDC 400V input or increased DC voltage output designs can be utilized to achieve this purpose.In order to ensure power stability when high-power servers are operating, power modules with hot-swappable redundant power supply specifications (such as CRPS) have been widely applied in server racks. Power modules with redundant functions require testing of multiple power modules at a time to ensure that all modules can maintain normal operation during high power output. Due to the rapid changes in the development of server power supplies, GW Instek developed the brand new flagship model ASR-6000 series to meet customer needs.The ASR-6000 series has two models - ASR-6450 AC / DC 4.5kVA and ASR-6600 AC / DC 6kVAASR-6000 is the first stand-alone unit from GW Instek that supports AC single/three-phase input and output, and has rated DC power output. The series employs third-generation semiconductor silicon carbide (SiC) technology to create a 4U 6kVA high power density and high-performance AC /DC power source.ASR-6000 has the ability to emulate more diverse power environment changes, such as balanced three-phase and unbalanced three-phase, phase loss, and features multi-channel output function can test up to three DUTs at the same time, programmable output impedance adjustment, and built-in over 40 types of arbitrary waveform outputs. The invincible launch of GW Instek flagship model ASR-6000 demonstrates that GW Instek can provide a complete test solution for high-power AC sources. ASR-6000 is the MVP of GW Instek power sources.ASR-6000 main applicationServer/communication power supply manufacturer6kVA On-board chargerUninterruptible power supply system (UPS)AC inverterAC three-phase motor control, and protection deviceMilitary industry, scientific research, educationFeaturesAdopts third-generation semiconductor silicon carbide (SiC) technology to create a 4U 6kVA high-performance AC/DC power source with high power densityAC input supports single-phase and three-phase, phase voltage 200V to 240V±10% (Delta or Y connection)10 output modes: including external input signal frequency and mains synchronization (SYNC), external voltage controlled internal amplifier output (VCA)Multi-channel output functionSupports 1P2W, 1P3W, 3P4W outputAC maximum output phase voltage: 350Vrms line voltage: 700VrmsAC balanced and unbalanced three-phase, phase loss output functionsProgrammable output impedance adjustmentDual-channel voltage/current output monitoring functionVoltage output rise time can be adjusted in three rangesSupports sequence editing and emulation output modePowerful arbitrary waveform editing and output function, capable of editing and outputting tens of thousands of waveformsAdvanced web server control to support data acquisition function100th order harmonic measurement functionSupports external parallel connection to increase output powerStandard interfaces: RS-232C, USB, LANOptional interfaces: CAN Bus, DeviceNet, GPIB